BL1.3W:SAXS/WAX

Welcome to BL1.3W

SAXSNanostructure 1–100 nm

WAXSCrystalline structure & crystallinity

SAXS + WAXSMeasured simultaneously

XRFElemental composition

BL1.3W uses synchrotron light from a Multipole Wiggler — a permanent-magnet insertion device installed in the storage ring that generates a 2.2 Tesla magnetic field, producing the intense, broad-spectrum X-rays used at this beamline. SAXS determines particle size, shape and structural organization at the nanometer scale for nanoparticles, polymers and fibers, and biological nanostructures; WAXS probes crystalline structure from polymers and biological materials to inorganic crystals; and both length scales can be measured at the same time on a single sample. XRF identifies elements whose absorption edges are below the 9 keV incident energy.

Beamline Layout & Specification

2.2 TMultipole wiggler

6–9 keVPhoton energy (optimized at 9 keV)

~2 × 10⁹Photon flux (phs/s)

0.4 mradBeam divergence

Schematic layout of BL1.3W from the source to the Experimental Hutch — BL1.3W beamline layout, from source to Experimental Hutch (schematic, not to scale)

The light source is shared by three parallel beamlines — BL1.1W, BL1.2W and BL1.3W — each divided into the Front End (FE), Optics Hutch 1 (OH1), Optics Hutch 2 (OH2) and the Experimental Hutch (EH). A Double Multilayer Monochromator (W/B₄C, 150 layers at 2.5 nm per layer) selects a working energy of 9 keV (1.38 Å), tunable across 6–9 keV, and a toroidal focusing mirror focuses the beam onto the sample position. The beam travels through a vacuum tube to a beryllium window; measurements are made by opening the beam shutter and triggering the detector at the same time under computer control.

Experimental Station

Rayonix SX165SAXS / WAXS · 2048 × 2048 px · ~80 µm pixel

Rayonix LX170Simultaneous SAXS/WAXS · up to ~140 fps

Vortex® SDDXRF · ≤130–150 eV at 5.9 keV

SAXS measurement setup: X-ray beam, sample, vacuum flight tube and 2D detector — SAXS measurement setup

WAXS measurement setup: X-ray beam, sample and 2D detector at wide scattering angles — WAXS measurement setup

The Rayonix SX165 is a 2D CCD detector with a Ø165 mm active area, 16-bit dynamic range and DQE up to ~0.8 at 8–12 keV. The Rayonix LX170 has an 85 × 170 mm² active area with a notch that lets the direct beam and SAXS signal pass through while collecting WAXS data, making it ideal for simultaneous SAXS/WAXS (44 µm pixel at 1×1, dead time ~1 ms). For XRF, a single-element Vortex® silicon drift detector covers ~1–30 keV with Peltier cooling.

Sample Environments

500 NIn-situ tensile stage · up to 40 cm elongation

5–200 °CIn-situ heating stage (Cu cell)

−100–270 °CSAXS temperature sweep

34 / 17Solid / liquid samples per sample-changer cycle

SCG tensile stage set up at BL1.3W — In-situ tensile stage

Cu heating cell with heating rods at BL1.3W — In-situ heating stage

Instec temperature sweep system with mK2000 controller at BL1.3W — SAXS temperature sweep

BL1.3W offers sample environments for in-situ SAXS/WAXS. Two tensile stages stretch samples with a maximum force of 500 N — the SCG stage (up to 40 cm elongation, heating to 200 °C) and the beamline stage (up to 20 cm, heating to 100 °C). A Cu heating cell controlled by a Eurotherm 2116 covers 5–200 °C with a freely programmable heating rate, while the Instec temperature-sweep system (mK2000 controller) provides precise cooling and heating from −100 to 270 °C. Automatic sample changers handle up to 34 solid or 17 liquid samples per cycle for efficient sequential measurements.